Uploading /data/ha-glow-varmepump/.pioenvs/ha-glow-varmepump/firmware.binįeatures: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None INFO Running: platformio run -d /config/esphome/ha-glow-varmepump -t upload -upload-port /dev/ttyACM2ĪVAILABLE: esp-prog, espota, esptool, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa Retrieving maximum program size /data/ha-glow-varmepump/.pioenvs/ha-glow-varmepump/firmware.elfĬhecking size /data/ha-glow-varmepump/.pioenvs/ha-glow-varmepump/firmware.elf Library Manager: Already installed, built-in library HARDWARE: ESP32 240MHz, 320KB RAM, 4MB Flash Processing ha-glow-varmepump (board: nodemcu-32s framework: arduino platform: platformio/ ) INFO Running: platformio run -d /config/esphome/ha-glow-varmepump This is the output: INFO Reading configuration /config/esphome/ha-glow-varmepump.yaml. It was interesting to connect the board to my computer running HA and ESPHome. It connects and I can see the following screen in the console: bin file compiled above and press “Flash ESP”. I connect my board to the windows computer, start esphome-flasher. I start by in Home Assistant ESPHome gui chose install and chose “Manual download” to get a. Via esphome-flasher 1.3.0 for Windows 圆4.It stops after ~15 s and says “Installation failed”. Then it says “Installing… it can take two minutes”. I can see that ESPHome connects (it says “Connecting” and then “Preparing installation”). I hold the boot button on the board, chose the correct serial port and press “Connect”. I have connected my board via USB to my Windows computer and chose “Plug into this computer”. Now I have tried two ways to flash my board: In ESPHome web gui I add a new entity where I put a configuration for HA Glow and the IP address thing added above.That failed and now I can’t flash it at all… I have two Home Assistant Glow and after upgrading one of them to have a dedicated IP address I then tried to do the same thing for the other HA Glow. Unexpected error: Error while erasing flash: Timed out waiting for packet content The console says this: Using 'COM5' as serial port. I started esphomeflasher as Administrator on my windows machine… Unexpected error: could not open port 'COM5': PermissionError(13, 'Åtkomst nekad.', None, 5) I get the following error message: Using 'COM5' as serial port. I downloaded the esphomeflasher and tried with the compiles ha-glow.bin that I compile via esphome. I have put the board in boot mode by pushing the boot button on the board before I chose the serial device. # Sensors for ESP version and WIFI information # Enable fallback hotspot (captive portal) in case wifi connection fails # meter, useful if you do not have a serial port (P1).ĭevice_description: "Measure your energy consumption with the pulse LED on your smart meter" # Read your electricity meter by means of the pulse LED on your Here is the config file for the second HA Glow: # Home Assistant Glow When I try to install the second HA Glow it builds the software an starts installing but failes after 20 seconds with the following message:Īnyone who knows what can be the problem? When I validate the config file there are no problems. The only difference between the two yaml files are the device_name and the friendly_name. When I install the second HA Glow it just failes. I copied the yaml file and changed the names. I have successfully installed ESPhome on the first HA Glow according to instruction in the link and it measures energy for me. I have mounted all component as described in the short description in the link for two HA Glow. I have bought the components and I have printed the cases. I would like to measure energy with Home Assistant Glow.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |